Water is dripping onto the sales floor, a ceiling tile just dropped in the server room, or the stockroom has buckets lined up again. Call Metal Roofing in Bucks and we connect you with an independent commercial roofer who works on TPO, EPDM, PVC, mod-bit and built-up roofs, often with crews that can work around your tenants.
A low-slope roof does not shed water the way a pitched roof does. It holds it briefly and relies on a continuous membrane, a few drains and gravity to move it off. When one of those fails, water slips through a seam, a split at a pitch pan or a gap under a coping cap, then travels sideways through the insulation before it ever shows up inside. That is why the leak over the checkout lane can start at a curb three bays over.
The people calling about Commercial Roofing are usually property managers, facility leads and business owners, not roofers. They need three answers: what failed, whether it can be repaired or needs a bigger fix, and what it costs to keep the building open while the work gets done. The right contractor answers with core samples, moisture data and marked-up photos, not a reflexive pitch for a new roof.
On a business, timing is half the job. A wet ceiling over inventory means lost stock and claim paperwork, and a leak over a dining room means a closed section on a Friday night. Plenty of the independent roofers we connect callers with will stage loud or smelly work, like torch-down or hot asphalt, for off-hours so the building keeps running.
A shingle crew is not a membrane crew. We route Commercial Roofing calls to independent contractors who work on low-slope systems every week.
Work on a commercial roof usually carries a separate license class in many jurisdictions, bigger liability limits and workers' comp coverage. The independent pros we route you to can send a certificate of insurance naming your property or management company as additional insured, which most landlords require before anyone sets a ladder. Ask for it and check the expiration date.
When water is coming through the deck, the first goal is stopping it, not writing a proposal. Depending on availability, a local contractor can often get someone up to clear a clogged drain, cut out a wet section or set a temporary mastic and fabric patch the same day or night. Permanent repairs get scoped once the roof dries out enough to diagnose properly.
Commercial bids should be itemized by square footage, membrane type and thickness, insulation R-value, flashing details and the number of drains and curbs. That lets you compare repair, restoration and replacement side by side and hand ownership something clean. The contractor writes the quote, explains their own workmanship terms in writing, and tells you whether the system can be registered with the membrane manufacturer.
Low-slope work runs on gear most residential crews never touch: robotic hot-air welders and seam probes for TPO and PVC, torches and kettles for mod-bit and built-up roofs, and airless rigs for coatings. Many contractors also bring infrared cameras or capacitance meters to map wet insulation before anything gets cut.
Every low-slope system has its own weak points, and the fix depends on what is actually on the roof. These are the jobs that come through our line most often.
With TPO and PVC, seams are heat-welded, and the usual culprits are a weld that never fused, a foot-traffic puncture or an unpatched T-joint. The contractor probes the seams, cleans and preps the sheet, and welds in matching material. Weathered TPO sometimes will not weld cleanly, and that alone tells you something about remaining life.
EPDM is forgiving and long-lived, but its seams rely on tape or adhesive, and both let go with age and shrinkage. A repair usually means scrubbing with primer, applying cover tape or a cured patch, and re-securing perimeter flashing that has tented. If the membrane has shrunk hard at the edges, expect the contractor to talk about a perimeter re-flash.
Multi-ply asphalt roofs handle foot traffic well, though they develop blisters, cracked cap sheet and split flashing at walls as they age. Repairs can be torch-applied, cold-applied or mopped in hot asphalt, depending on the deck, the occupancy and the fire watch rules on site. Gravel-surfaced roofs may need the aggregate scraped back first.
Water still standing 48 hours after rain is ponding, and most membrane makers do not like it. Contractors clear strainers and leaders, reset drain clamping rings, add crickets behind curbs and use tapered polyiso to rework low spots. A deck that sags between joists is past a roofing fix and may need an engineer.
Plenty of so-called roof leaks start at the edges and penetrations, not in the open membrane. Loose coping caps, open parapet joints, failed counterflashing and rooftop unit curbs with short base flashing let water in behind the sheet. The fix is often re-flashing the wall, adding coping cleats and sealant, or raising curb flashing to the height the manufacturer calls for.
A fluid-applied silicone or acrylic system can extend a tired but dry roof without a tear-off. That is the catch: coating over wet insulation just seals the problem in. Expect an infrared scan at dusk, a capacitance meter grid or core cuts before anyone recommends a coating.
Here is what happens after you call about a commercial roof, from the first question to the last photo.
Tell the dispatcher the building use, roughly how big the roof is, the membrane type if you know it, and where water is showing inside. Mention roof access, whether there is a hatch or the crew needs a lift, and any tenant hours to work around.
A local commercial contractor follows up to confirm access and timing, which in many areas is the same day, depending on availability. For active leaks, the first visit is about clearing drains, finding the entry point and making a temporary seal.
Expect seam probing, a look at each penetration and drain, moisture readings and possibly a core cut to see what is under the membrane. You get a written scope with photos and options, usually repair, restore or replace.
After the job, ask for before-and-after photos and a marked-up roof plan so your files show what was repaired and where. Those records help with the next capital budget and any insurance question.
These typical situations, blended from many calls, show what to expect.
After a heavy rain, a warehouse lead found water on wrapped pallets beneath a row of skylights. The independent contractor found two clogged interior drains and a split in the TPO at a skylight curb corner. The drains were cleared that evening, the curb was welded the next morning, and the manager had photos to send the owner. The roof itself had years left.
A restaurant owner had a drip landing between two booths every time it rained hard. The contractor traced it to the kitchen exhaust fan curb, where grease had softened the EPDM and the base flashing had pulled loose. The repair was done before opening hours, the damaged rubber around the curb was cut out and re-flashed, and a grease containment box went on the fan so the new flashing would not soften the same way. Service was not interrupted once.
A property manager was handed a quote to coat an old mod-bit roof over an office building and wanted another opinion first. The second contractor ran an infrared scan at dusk and pulled cores, which showed wet insulation across roughly a fifth of the roof. Instead of coating over wet sections, the plan became removing them, installing new polyiso, and then coating.
These are composite examples of the kinds of calls we route, written to show how the process works. They are not individual customer reviews.
It depends mostly on what is under the membrane. If a moisture survey shows the insulation is largely dry and the membrane is just weathered, repair or a restoration coating often makes sense. If a big share of the insulation is wet, or there are already two roofs on the building, replacement is usually the honest answer. The contractor should show you the cores and readings behind the recommendation.
Usually, yes. Many independent commercial contractors schedule tear-off, torch work and hot asphalt for nights, early mornings or weekends, and they can rig debris protection over sensitive areas inside. Tell the dispatcher about tenant hours, dock schedules and odor-sensitive spaces like food service or medical offices so the right contractor is matched.
A common rule of thumb in the trade is 48 hours. Water that clears within two days of rain is normal on a low-slope roof. Water still sitting after that is ponding, which adds weight, breaks down some membranes faster and can affect manufacturer coverage. The fix ranges from clearing a strainer to adding tapered insulation or crickets.
It depends on how the building is used. Restaurants and anything venting oils tend to do better with PVC. Big-box and warehouse roofs often go TPO for reflectivity and price. EPDM suits simple roofs with few penetrations, and mod-bit makes sense where maintenance staff walk the roof often. Your hold period matters as much as the material.
Pull together what you have: original install paperwork, old repair records, leak photos with locations marked on a floor plan, and access instructions. Let building security know a roofer is coming. The more the contractor knows before climbing up, the faster the source gets found.
We route calls from all over Markham and the surrounding area, from small strip centers to big distribution buildings. The independent contractor you are connected with is local enough to come back for follow-up work, which matters on roofs that need regular attention.
Managing more than one property? Say so when you call, since some contractors can handle a portfolio under one contact and one schedule.
Call Metal Roofing in Bucks any time and we will connect you with an independent low-slope contractor near Markham. The referral is free and there is no obligation.
